Easy Coop Maps Portal 2 Dr Fauli

This is a guide on how you can test co-op maps alone utilizing the splitscreen capabilities of the Source engine. This also works for any existing coop maps. It does not require any modifications to the map file itself.

This does not cover the requirements for making a coop level in the first place.

Contents

• 1 Loading the Map
  • 1.1 Dual Monitors
• 2 Controlling the Second Player
  • 2.1 in_forceuser
  • 2.2 Use a Controller
  • 2.3 change_portalgun_linkage
• 3 Other Useful Console Commands
• 4 External Links

Loading the Map

ss_map mapname

Load mapname in splitscreen 2-player mode. Analogous to map in singleplayer. Like map, it is not required to add the trailing .bsp.

 Note: If the map name doesn't begin with "mp_coop_", add " *mp" to the end of the command: ss_map mapname *mp

ss_splitmode mode

Changes the splitscreen mode.

ss_splitmode 0: Use recommended settings based on width

ss_splitmode 1: Top-and-bottom split

ss_splitmode 2: Side-by-side split

If your map is stuck at the loading screen, try to shorten the VMF filename and recompile.

Dual Monitors

If you run dual monitors and want to split to each monitor, follow this guide

Controlling the Second Player

If you could actually play the coop map entirely as one player, it wouldn't be a very cooperative map. These are some ways you can control the second player.

in_forceuser

in_forceuser playerindex

Take over the second player. All movement and other keybindings will be as if the second player used them. Requires cheats to be enabled.

sv_cheats 1: Turn on cheats

in_forceuser 0: Control player #1 (Atlas)

in_forceuser 1: Control player #2 (P-Body)

To make this easy to use, set a keybinding for it:

BindToggle "z" in_forceuser

Swaps you between first and second player when you push "z".

 Note: If you are moving, crouching, shooting portals or otherwise performing an action when you change players, you will stop during the change but immediately resume the action when you change back. For instance, if you're holding "w" to move forward, you will stop moving forward as soon as you hit "z" (assuming you use the BindToggle above), but immediately resume moving forward when you hit "z" again even if "w" is no longer being held down. To stop this, simply tap "w" again, or use a more robust keybinding: Bind "z" "-moveleft; -moveright; -use; -forward; -back; -attack; -attack2; toggle in_forceuser".

Use a Controller

This is actually more complicated than it sounds unless you have two controllers available. Source will map actions of the first detected controller to the first player and there doesn't seem to be any way to override this. The workaround is to either have two actual controllers or use trickery to make your computer think it has two controllers.

You can also connect one controller and enter command in_forceuser 1. Then, Atlas will be controled by controller and P-body will be controled by keyboard.

 Bug: Portal icons on the screen will get swapping, because primary portal is on left when playing with keyboard and on right when playing with controller.

More information for this can be found on the Steam forums.

change_portalgun_linkage

This allows you to use the extra sets of linked portals without actually changing characters.

change_portalgun_linkage_id integer

Changes portals fired to belong to the specified character or team.

change_portalgun_linkage_id 0 : Single-player

change_portalgun_linkage_id 1 : Blue

change_portalgun_linkage_id 2 : Orange

change_portalgun_linkage_id [3-9] : Extra / Reserved

 Note: The color appearance of portals is tied to the person firing them. E.g., when Blue fires Orange's portals (linkage_id: 2), they appear blue until Orange fires them again.

Other Useful Console Commands

cmd2 command

Executes command as if typed by the second player.

cmd2 name Player2: Sets the name of the second player

ss_force_primary_fullscreen enable

Makes the first player fullscreen if enable is 1, hiding the second player's view.

ss_pipsplit 3; ss_pipscale 1; ss_pip_bottom_offset 0; ss_pip_right_offset 0 can be used to show only the second player's view

External Links

• Original version of this guide hosted at ThinkingWithPortals.com
• How-to: Split Screen Coop
• How-to: SplitScreen with 2 monitors
• How-to: Play Co_Op Alone

hoffmandequed1982.blogspot.com

Source: https://developer.valvesoftware.com/wiki/Testing_Portal_2_Co-Op_Maps_Alone